Please tick your settings to determine the appropriate solutions.

ANTISLIP ADHESIVE TAPES

Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings. Suitable for any type of base material: rough floors, painted floors, tiling, marble, stone, timber, aluminium, metal stairs, access ramps. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Rolls of different widths: 25 mm, 50 mm, 100 mm, 150 mm, other widths available between 9 mm and 1,000 mm. Standard rolls of 18.30 m. Roll of carborundum in standard colours: black, grey, white, yellow, clear, blue, green, red, brown or bright colours (fluorescent yellow...). Rolls or stripes in single or two colours black/yellow, red/white, etc. All Pantone and RAL colours or special colours according to quantities. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings.

Learn more

BACKER RODS

In accordance with relevant standards (French SNJF and ISO), the joint backing is a material that is laid to limit the depth of the sealant in the joint and to define the back profile of the joint. It stops the sealant from adhering to the three faces of the joint and helps to resist the pressures that occur when apply the sealant. The joint backing must not have any effects that will change the physical and chemical properties, and even the appearance, of the sealant. It can eventually serve as a barrier to separate the sealant for chemical attacks from the bottom side of the joint. The joint backing is used as a permanent formwork when applying a sealant or any other finish. It is used to limit the depth of sealant that is applied. It is recommended for use with the following sealants: silicone, polyurethane, polysulphide, acrylic. Recommended by SNJF (French institute for the classification of plastic and elastomeric sealants) as air and water seal in construction, as well as a seal in formworks. Grey closed-cell polyethylene foam. Available in diameters from 10 mm to 100 mm, supplied in coils or in length according the the diameter used. Grey foam supplied in coils or lengths. The joint backing is used as a permanent formwork when applying a sealant or any other finish. It is used to limit the depth of sealant that is applied. It is recommended for use with the following sealants: silicone, polyurethane, polysulphide, acrylic. Recommended by SNJF (French institute for the classification of plastic and elastomeric sealants) as air and water seal in construction, as well as a seal in formworks.

Learn more

BLANKETS VEDAFEU M ©

For initial joint widths from 100 to 420 mm, with or without joint cover. Officially rated EI 120 minutes without failure. Tests were performed with a + 40 % movement. Not hazardous for human health : VEDAFEU M © blankets are made of bio-soluble fibers and do not contain any asbestos nor classified refractory ceramic fibers. VEDAFEU M © composition and installation method are fully patented.

Learn more

BLANKETS VEDAFEU N ©

Our VEDAFEU N fire stop joint range, including fire stop joint covers and fire blankets, conforms to several certifications in respect of horizontal and vertical joints. These fire stop joint covers are specially designed to ensure the fire integrity and gas-tightness of expansion joints with large gaps and/or large movements. Tested with movements of +50%, all our VEDAFEU N fire blankets have an EI classification for fire integrity and gas-tightness, in compliance with current European and French standards, including EN 13501-2 and EN 1366-4 norms. VEDAFEU N fire stop joint covers are available in several sizes to suit joint gaps from 100 mm to 840 mm. VEDAFEU N fire stop joint covers can be used for horizontal and vertical joints requiring fire stop joint protection, e.g. floor, wall and ceiling joints, joints between prefabricated façade elements, and seismic joints. They are also suitable for fire partitions, conduit penetrations, services ducts, protection of neoprene supports, and for joints on plate edges. VEDAFEU N fire stop joint covers must be installed in accordance with the approved instructions for the relevant classification certifications. VEDAFEU N systems provide effective protection for buildings that house works of art, as well as for hospitals, offices, industrial and residential buildings, hotels, shopping centres, car parks, schools, colleges, stations, airports, stadiums, and more. The composition of VEDAFEU N fire stop blankets and their method of installation are patented. Handling is easy and safe: VEDAFEU N fire stop blankets do not contain any asbestos (which is a banned substance) or refractory ceramic fibres which are dangerous to health. This is because they are manufactured with long mineral fibres that exceed 6 microns in diameter and which cannot enter the respiratory tract, and are thus classified as not dangerous to health by the International Agency for Research on Cancer (IARC). Our standard range is suitable for joints with initial gaps from 100 mm to 560 mm. Other widths are available on request.

Learn more

BLANKETS VEDAFEU SV ©

Solutions for standard or seismic joints. Without mechanical fixing Tested and certified up to + 275% expansion.

Learn more

BUTYL STRIP

Veda's butyl strip is a cold adhesive strip made up of an adhesive butyl backed by an aluminium-reinforced polyester film. The adhesive face is protected by a peel-off silicone backing and offers an excellent tear resistance. The butyl strip provides a water and vapour barrier. It is recommended for the repair of membrane tears or holes as well as the protection of mechanical joint anchors.

Learn more

CJ Alu

Our aluminium joint covers are aesthetical, and easy to install, suitable for joints gaps from 10 mm to 150 mm. They are available from stock in 3m lengths in the following widths for flat sections: 50 mm, 60 mm, 70 mm, 90 mm, 120 mm, 140 mm, 180 mm, and 210 mm, and in these widths for angle sections: 50 mm, 60 mm, 70 mm, 90 mm and 120 mm.The Clip affixed aluminium joint covers are used in new constructions and in refurbishment projects, indoors or outdoors, in joints from 10-mm to 150-mm wide in walls, ceilings and floors (pedestrian use). They are installed easily by means of clips (clip sizes S, L, XL and XXL). They are fully compatible with our Vedafeu C fire barrier cords and beads, Vedafeu N blankets and Vedafeu M matresses. Made of 6063 T6 aluminium alloy, plain or with 15-micron anodised finish in clear colour. The number that follows indicates the width in millimetres of the joint cover. Aluminium joint covers can be supplied with powder coat finish in any RAL colour on demand; please enquire. All types can be supplied with plain finish or anodised finish, cut to length and/or drilled; for quantities and conditions, please enquire.

Learn more

CJ Brass

Our brass joint covers are also available in different clip sizes for particular joint gaps, from 10 mm to 70 mm. These products are available from stock in 3m lengths, in flat section of 90 mm only. The Clip affixed brass joint covers are used in new constructions and in refurbishment projects, indoors or outdoors, in joints from 10-mm to 70-mm wide in walls, ceilings and floors (pedestrian use). They are installed easily by means of clips (clip sizes S, L, XL and XXL). They are fully compatible with our Vedafeu C fire barrier cords and beads. Made with extruded brass, we can also supply special sections on request. Brass joint covers are supplied in rough pressed finish.

Learn more

CJ PVC

Our clip-on building expansion joint covers in PVC can be used either indoors or outdoors, for interior wall expansion joints, ceilings and floors (light use). They come in a variety of clip sizes to suit 10 mm to 120 mm joint gaps, and are available from stock in 3m lengths, in flat sections of 50 mm, 70 mm, 90 mm and 150 mm, and in angle sections of 50 mm, 70 mm and 90 mm. Clip-on PVC building expansion joint covers are used in new constructions and in refurbishment projects, for 10mm to 120mm interior wall expansion joints, as well as ceilings and low-traffic floors. They are installed easily by means of clips (sizes S, L, XL and XXL) and are fully compatible with our Vedafeu fire stop products. Flat covers for interior wall expansion joints, facades and ceilings have a W reference. Flat building expansion joint covers for floors have an LF reference for light duty floors, and an F reference for heavy duty floors with intense traffic of pedestrians and light trolleys up to 6kN. Angle building expansion joint covers have the same references preceded by the letter E, i.e. EW, ELF... The number that follows indicates the width in millimetres of the joint cover. Standard PVC building expansion joint covers are available in white (RAL 9016), beige (RAL 1015) and grey (RAL 7035). For other colours, please contact us.

Learn more

CJ Stainless steel

The clip affixed stainless steel joint covers are designed to provide an attractive and decorative solution to the problem of protecting and concealing expansion joints (façades, walls and ceilings). Fast and easy to install: no drill or fixing required. They are suitable for use in new or refurbishment projects, inside or outside. They can be installed in any kind of building: shopping malls, office buildings, hospitals, etc. They resist to agressive environments (corrosion, salty air, high temperature, frost, etc.). To accomodate any of your needs, the following finishes are available: mill finish, brushed 220 grit, high gloss polished or leather-like stainless steel.

Learn more